UCS-NVM2-960GB= Hyperscale Non-Volatile Memor
Core Hardware Architecture & Protocol Stack The ...
Overview of the NIM-2MFT-T1/E1++= Module
The Cisco NIM-2MFT-T1/E1++= is a high-density, multi-service network interface module designed for ISR 4000 series routers. Engineered to support T1 (1.544 Mbps) and E1 (2.048 Mbps) circuits, this module enables enterprises and service providers to consolidate legacy TDM (Time-Division Multiplexing) infrastructure with modern IP-based networks.
Key hardware attributes include:
- Dual-port architecture with independent clocking for mixed T1/E1 deployments.
- RJ-48C connectors compliant with ANSI T1.403 and ITU-T G.703/G.704 standards.
- Enhanced DSP (Digital Signal Processor) for low-latency voice, video, and data traffic.
- Hardware-based CRC (Cyclic Redundancy Check) for error detection on Layer 1.
Hardware Compatibility and System Requirements
The NIM-2MFT-T1/E1++= operates exclusively with Cisco ISR 4400 series routers, including the 4451-X, 4331, and 4351 models.
Deployment prerequisites:
- Cisco IOS XE Fuji 16.9.1 or later for full feature support.
- Power requirements: 6.5W per module, with PoE+ compatibility on supported routers.
- Thermal constraints: Operates at 0°C to 40°C; airflow clearance of 2 inches required.
Protocol Support and Configuration Scenarios
This module bridges legacy telecom systems and SD-WAN architectures. Below are common use cases:
1. Legacy PBX Integration
The NIM-2MFT-T1/E1++= supports CAS (Channel Associated Signaling) and CCS (Common Channel Signaling) modes for analog/digital PBX connectivity. For SIP trunking, configure T1/E1-to-IP gateway functionality using Cisco Unified Border Element (CUBE).
Sample CLI snippet for PRI configuration:
controller T1 0/2/0
framing esf
clock source internal
linecode b8zs
pri-group timeslots 1-24 2. Frame Relay Backhaul
Enterprises migrating from Frame Relay to MPLS/IPsec can use the module as a Frame Relay DCE (Data Circuit-Terminating Equipment). Enable FRF.12 fragmentation and LFI (Link Fragmentation and Interleaving) to prioritize voice traffic over low-speed links.
3. Cellular Failover with LTE Backhaul
Pair the NIM-2MFT-T1/E1++= with a Cisco NIM-4G-LTE module for hybrid WAN redundancy. Configure Performance Routing (PfR) to switch traffic to LTE during T1/E1 outages.
Performance Benchmarks and Limitations
Cisco’s internal testing reveals:
- Latency: < 5 ms for 64-byte packets at 95% load.
- Jitter: 1 ms sustained under G.711 voice traffic.
- Throughput: Full T1/E1 line rate (1.544/2.048 Mbps) with HDLC or PPP encapsulation.
Key limitations:
- No support for STM-1/OC-3 or higher SONET/SDH speeds.
- Channelized T1/E1 requires licenses for >8 DS0 groups.
Addressing Common Deployment Challenges
Q: How to troubleshoot CRC errors on T1 links?
A: Verify line code alignment (b8zs for T1, hdb3 for E1) and ensure CSU/DSU devices match clocking settings. Use show controller t1 0/2/0 to identify framing errors.
Q: Can this module handle fractional T1/E1?
A: Yes. Configure timeslots 1-6 (or custom ranges) in channelized mode to allocate bandwidth granularly.
Licensing and Warranty Considerations
The NIM-2MFT-T1/E1++= requires a Cisco ONE Software subscription for advanced features like NetFlow and IP SLA. Base functionality operates under the IOS XE Advantage License.
For procurement, visit the NIM-2MFT-T1/E1++= product page at itmall.sale.
Final Evaluation: Balancing Legacy and Modern Needs
While SD-WAN dominates enterprise discussions, the NIM-2MFT-T1/E1++= remains indispensable for industries like utilities, healthcare, and banking, where TDM-based SCADA systems or ATM networks persist. Its ability to handle strict SLAs for jitter-sensitive applications justifies its role in hybrid environments. However, organizations must weigh the cost of maintaining T1/E1 circuits against gradual migration to Ethernet or 5G alternatives. Cisco’s continued investment in this module signals its relevance in transitional network architectures.